Inspiron 700m Wireless configuration on Kubuntu
I have a Dell Inspiron 700m. I have Kubuntu Breezy Badger 5.10 on this box.
This is how I got the WiFi going on this beauty.
1. Boot up into windows and get the Intel Driver from Intels 1st site OR Intels 2nd site
2. Save the files into a location on the drive which is accessible through linux.
root@trance:/home/trance# ls -al /media/hda1/intel/wireless_9.0.4_generic_109116/Drivers/
total 8680
dr-x—— 1 root root 4096 2006-05-14 05:42 .
dr-x—— 1 root root 4096 2006-05-14 05:42 ..
-r——– 1 root root 188416 2005-12-27 23:53 SetupWLD.EXE
-r——– 1 root root 4849 2005-01-25 15:17 SetupWLD.ini
-r——– 1 root root 13 2006-02-02 12:38 verfile.tic
-r——– 1 root root 1671168 2006-01-27 08:50 W29MLRES.DLL
-r——– 1 root root 2956544 2006-01-17 21:34 w29n50.sys
-r——– 1 root root 14821 2006-02-02 00:47 w29n51.cat
-r——– 1 root root 119785 2006-01-18 15:47 w29n51.INF
-r——– 1 root root 3325312 2006-01-17 21:32 w29n51.sys
-r——– 1 root root 466944 2006-01-27 08:49 W29NCPA.DLL
-r——– 1 root root 122880 2005-12-27 23:53 WLDMLRES.DLL
root@trance:/home/trance#
3. Go back into Kubuntu and get the ndiwrapper-utils, ndisgtk, ndiswrapper-source using
root@trance:/home/trance# sudo apt-get install ndiswrapper ndisgtk ndiswrapper-source
4. As root ndiswrapper -i will use the windows inf file to install the wireless driver. ndiswrapper -l lists the driver installed.
example:
root@trance:/home/trance# ndiswrapper -i /media/hda1/intel/wireless_9.0.4_generic_109116/Drivers/w29n51.INF
root@trance:/home/trance# ndiswrapper -l
Installed ndis drivers:
w29n51 driver present, hardware present
root@trance:/home/trance#
5. modprobe ndiswrapper checks if the ndiswrapper kernel module is installed. An installed module will result in no error. Then write the config file such that you do not need to go through the earlier steps every time you restart the system.
root@trance:/home/trance# modprobe ndiswrapper
root@trance:/home/trance# ndiswrapper -m
Adding “alias wlan0 ndiswrapper” to /etc/modprobe.d/ndiswrapper
6. If some error occurs check the output of lsmod
root@trance:/home/trance# lsmod | grep ndiswrapper
7. Now that your ndiswrapper is installed and configured. We now need to start up the wireless interface. On my box the wireless interface used to show up as eth0, however, it was not configured to use the ndiswrapper so I would get ‘segmentation fault’ on doing ifup eth0.
However, with the drivers set, I checked if all was well.
root@trance:/home/trance# iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
eth0 IEEE 802.11g ESSID:”MySSID”
Mode:Managed Frequency:2.437 GHz Access Point: 00:13:46:46:78:28
Bit Rate=54 Mb/s Tx-Power=20 dBm
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX Security mode:open
Power Management:off
Link Quality=97/100 Signal level=-27 dBm Noise level=-89 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
root@trance:/home/trance# ifconfig
eth0 Link encap:Ethernet HWaddr 00:13:CE:D9:0D:74
inet6 addr: fe80::213:ceff:fed9:d74/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:48 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:236683 (231.1 KiB) TX bytes:1104 (1.0 KiB)
Interrupt:10 Base address:0x8000 Memory:e0206000-e0206fff
eth1 Link encap:Ethernet HWaddr 00:12:3F:6B:36:2F
inet addr:192.168.0.109 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::212:3fff:fe6b:362f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3050 errors:0 dropped:0 overruns:0 frame:0
TX packets:1534 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3117901 (2.9 MiB) TX bytes:159050 (155.3 KiB)
Interrupt:10
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:33 errors:0 dropped:0 overruns:0 frame:0
TX packets:33 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2058 (2.0 KiB) TX bytes:2058 (2.0 KiB)
root@trance:/home/trance# ifup eth0
There is already a pid file /var/run/dhclient.eth0.pid with pid 0
Internet Systems Consortium DHCP Client V3.0.2
Copyright 2004 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP
sit0: unknown hardware address type 776
sit0: unknown hardware address type 776
Listening on LPF/eth0/00:13:ce:d9:0d:74
Sending on LPF/eth0/00:13:ce:d9:0d:74
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
ip length 328 disagrees with bytes received 332.
accepting packet with data after udp payload.
DHCPOFFER from 192.168.0.1
DHCPREQUEST on eth0 to 255.255.255.255 port 67
ip length 328 disagrees with bytes received 332.
accepting packet with data after udp payload.
DHCPACK from 192.168.0.1
bound to 192.168.0.101 — renewal in 241302 seconds.
root@trance:/home/trance# ifdown eth1
There is already a pid file /var/run/dhclient.eth1.pid with pid 6390
killed old client process, removed PID file
Internet Systems Consortium DHCP Client V3.0.2
Copyright 2004 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/products/DHCP
sit0: unknown hardware address type 776
sit0: unknown hardware address type 776
Listening on LPF/eth1/00:12:3f:6b:36:2f
Sending on LPF/eth1/00:12:3f:6b:36:2f
Sending on Socket/fallback
DHCPRELEASE on eth1 to 192.168.0.1 port 67
root@trance:/home/trance# ping www.google.com
PING www.l.google.com (64.233.161.99) 56(84) bytes of data.
64 bytes from 64.233.161.99: icmp_seq=1 ttl=233 time=73.5 ms
64 bytes from 64.233.161.99: icmp_seq=2 ttl=233 time=51.6 ms
— www.l.google.com ping statistics —
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 51.688/62.634/73.580/10.946 ms
8. To make sure that you don’t have to type iwconfig essid
iface eth0 inet dhcp
wireless-essid XXXXXXX
wireless-key XXXXXXXXXXXXXXXXX
My /etc/network/interfaces of Ubuntu (in FC/RHL this is the counterpart of the /etc/sysconfig/network-scripts/ifcfg-ethX)
looks like:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# This is a list of hotpluggable network interfaces.
# They will be activated automatically by the hotplug subsystem.
mapping hotplug
script grep
map eth1
# The primary network interface
auto eth1
iface eth1 inet dhcp
auto eth0
allow-hotplug eth0
iface eth0 inet dhcp
wireless-essid USC-Trojans
wireless-key # This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# This is a list of hotpluggable network interfaces.
# They will be activated automatically by the hotplug subsystem.
mapping hotplug
script grep
map eth1
# The primary network interface
auto eth1
iface eth1 inet dhcp
auto eth0
allow-hotplug eth0
iface eth0 inet dhcp
wireless-essid USC-Trojans
wireless-key 11111111111111111111111111